目录
创建admin VDC(可选)
创建一个VDC资源模板（可选）
创建VDC，并分配接口（分配接口可选）
初始化新VDC
检查配置
---------------创建admin VDC(可选)---------------
第一次启动时，" Do you want to enable admin vdc (yes/no) [no]:"，选择"yes"。适用场景：对于全新部署推荐该方式
在启动后， system admin-vdc ，Default VDC将转为Admin vdc，当输入该命令，在Default VDC中所有的非全局配置将会丢失。适用场景：当Default VDC仅用于管理，没有传输任何业务流量时，推荐使用
system admin-vdc migrate new vdc name，当输入该命令，在Default VDC的所有非全局配置迁移到一个新的VDC。适用场景：当Default VDC用于传输业务流量时，推荐该方式。
---------------创建一个VDC资源模板（可选）---------------
1. config t
2. vdc resource template vdc-template-name
3. limit-resource m4route-mem [ minimum min-value ] maximum max-value
limit-resource m6route-mem [ minimum min-value ] maximum max-value
limit-resource monitor-session minimum min-value maximum { max-value | equal-to-min }
limit-resource port-channel minimum min-value maximum { max-value | equal-to-min }
limit-resource u4route-mem [ minimum min-value ] maximum max-value
limit-resource u6route-mem [ minimum min-value ] maximum max-value
limit-resource vrf minimum min-value maximum { max-value | equal-to-min }
4. exit
5.(Optional) show vdc resource template
6.(Optional) show run { vdc | vdc-all }
7.(Optional) copy running-config startup-config
---------------创建VDC，并分配接口（分配接口可选）---------------
首先，必须以network-admin的角色登录到默认或admin VDC，步骤如下：
1. config t
!Creates a VDC and enters the VDC configuration mode.
! switch -Specifies the default VDC. VDC number 1 is reserved for the default VDC.
!Nondefault VDC numbers are from 2 to 9.
2. vdc { switch | vdc-name } [ ha-policy { dual-sup { bringdown | restart | switchover } [ single-sup { bringdown | reload | restart }] [ id vdc-number ] [ template template-name ] [ type storage ]
3.(Optional) [ no ] allocate interface ethernet slot/port
!注意"-"前后的空格
[ no ] allocate interface ethernet slot/port - last-port
[ no ] allocate interface ethernet slot/port , ethernet slot/port,...
4.(Optional) show vdc membership
5.(Optional) show vdc shared membership
6. exit
7.(Optional) show vdc
!After you create a VDC, you must copy the default VDC running configuration to the startup configuration so that a VDC user can copy the new VDC running configuration to the startup configuration.
8.(Optional) copy running-config startup-config
---------------初始化新VDC---------------
首先，必须以network-admin的角色登录到默认或admin VDC，准备新VDC mgmt0的IP地址
1. switchto vdc vdc-name
!Displays the current VDC number.
2.(Optional) show vdc current-vdc
---------------检查配置---------------
!Displays the VDC information in the running configuration.
show running-config { vdc | vdc-all }
!Displays the VDC configuration information.
show vdc [vdc-name]
!Displays the detailed information about many VDC parameters.
show vdc detail
!Displays the current VDC number.
show vdc current-vdc
!Displays the VDC interface membership information.
show vdc membership [ status ]
!Displays the VDC template configuration.
show vdc resource template
!Displays the VDC resource configuration for the current VDC.
show resource
!Displays the VDC resource configuration for all VDCs.
show vdc [vdc-name] resource [resource-name]
!Displays the MAC address for a specific VDC.
show mac vdc {vdc_id}